Hantek MPO6104D Oscilloscope 4 canaux 100MHZ + 2 Gén. AWG + 16 Anal. Logique
Oscilloscope à 4 canaux avec une bande passante de 100 MHz.
2 canaux de générateur de signaux arbitraires / fonctions.
16 canaux de l'analyseur logique.
1 GSa / s de période d'échantillonnage.
Capturez des taux allant jusqu'à 400 000 FPS.
Profondeur de mémoire de 64M.
Écran tactile capacitif WVGA (800x600).
16 types de fonctions de prise de vue.
Déclenchement et décodage de protocoles série (UART, CAN, LIN, SPI, IIC).
Fonction de génération de diagramme de Bode.
Hantek MPO6000D Series - Oscilloscopes à 4 canaux
Avec 2 générateurs AWG et 16 canaux d'analyseur logique
Caractéristiques:
- Oscilloscope six en un: oscilloscope 4 canaux + analyseur logique 16 canaux + générateur de forme d'onde 2 canaux + voltmètre numérique + analyseur de protocole série + analyse spectrale FFT.
- Fonction d'acquisition segmentée, prise en charge pour capturer jusqu'à 80 000 sections.
- Taux de capture de 60 000 wfms / s (affichage des points) / 400 000 wfms / s (mode d'acquisition rapide des points).
- Jusqu'à 16 types de fonctions de déclenchement, dont 5 types de déclencheurs de protocole.
Fournit 5 options de décodage série. - 1 GSa / s fréquence d'échantillonnage en temps réel des canaux analogiques.
Profondeur de mémoire standard de 64 Mpts. - Source de signal à 2 canaux, 13 types de formes d'onde à l'intérieur, 4 ensembles de formes d'onde arbitraires, taux d'échantillonnage de 200 M, longueur de forme d'onde de 8 Kpts.
- Taux d'échantillonnage en temps réel de 1 GSa / s des canaux numériques.
Faible bruit de base, plage dynamique verticale ultra large de 500 uV / div à 10 V / div. - Écran tactile capacitif WVGA 7 pouces, (800 * 480) TFT, avec écran ultra-large, image vivante, faible consommation d'énergie et longue durée de vie.
- Mesure automatique de 42 types de paramètres de forme d'onde (avec statistiques).
Voltmètre numérique 5 bits et fonction d'indicateur de fréquence matérielle 6 bits. - Fonction de diagramme de Bode (les oscilloscopes avec fonction de source de signal peuvent utiliser).
Fonctions d'opérations mathématiques à formes d'ondes multiples 【MATH function. Fonction de recherche d'événement. - Interfaces standard: périphérique USB, hôte USB, LAN, interfaces en option: HDMI, UART
Conforme aux normes d'instrument de classe LXI CORE 2011 DEVICE . Permettre la création et la reconfiguration rapides, économiques et efficaces du système de test.Supporte le contrôle à distance des commandes.
Model comparison
4-channel oscilloscope + 2CH AFG + 16CH LA - Digital fluorescence display and color temperature display
Bode diagram function - 256 grade color display
2-channel 25M waveform/Arb generator - Waveform capture rateup to 400,000
FFT function Scales show - Segmented acquisition and history waveform
16-channel digital channel - 64M memory depth
7 inch capacitive touch screen - 5 bits digital voltage meter , 6 bits frequency indicator
FFT function
Parameters
Oscilloscope function |
|||||
Acquisition | Real-time sample rate |
1 GSa/s(single channel) 500 MSa/s(two channels) 250 MSa/s(three/four channels) |
|||
Note:digital channel 12,34 open at the same time,it is considered as one channel | |||||
Peak detection | Analog channel 4ns | ||||
Note:digital channels don’t support | |||||
Average mode | Analog channel | ||||
All channels reach N time samples at the same time,N can be selected from 2、4、8、16、32、 64、128、256、512 and 1024. |
|||||
Note:digital channels don’t support | |||||
High resolution | Up to 12bit | ||||
Note:digital channels don’t support | |||||
Minimum test pulse width | 8ns | ||||
Memory depth | Single channel 64M | ||||
Two channels 32M | |||||
Input | Channel quantity | 4 analog channels | |||
Note:data channels can’t be opened | |||||
3 analog channels | |||||
Note:digital channel LA1/LA2/LA3/LA4/LA1LA2/LA3LA4 | |||||
2 analog channels | |||||
Note:digital channels infinitize | |||||
1 analog channel | |||||
Note:digital channels infinitize | |||||
0 analog channel | |||||
Note:digital channels infinitize | |||||
Input coupling | DC、AC or GND | ||||
Note:digital channels don’t support | |||||
Input impedance,DC coupling | Analog channel | ||||
25pF±3 pF,1MΩ±2% | |||||
Digital channel | |||||
(300KΩ±2%) ,(8 pF±3 pF) | |||||
Supported probe attenuation factor | Analog channel 1X、10X、100X、1000X | ||||
Voltage classes | 300V CAT II | ||||
Maximum input voltage | Analog channel 300VRMS (10X) | ||||
Digital channel -25V~25V | |||||
Horizontal | Waveform interpolation | (sin x)/x | |||
Maximum record length | Single channel maximum 64M | ||||
Two channels maximum32M | |||||
three/four channels maximum 16M | |||||
Horizontal scale range | |||||
2ns/div~100s/div 1, 2, 5 step by step | |||||
Time base mode | Y-T、X-Y、Roll | ||||
X-Y number | Channel 1,2 1 XY channel、channel3 4 1 XY channel | ||||
Zero offset | ±0.5 div× minimum time base gear | ||||
Sample Rate and | ±25ppm | ||||
Delay Time Accuracy | |||||
Clock drifting | ≤±5 ppm/year | ||||
Delta Time Measurement | single,“acquisition”mode | ||||
Accuracy | |||||
(Full Bandwidth) | ±(1 sample interval+100ppm×reading+0.6ns) | ||||
>16 times averages | |||||
±(1 sample interval+100ppm×reading+0.4ns) | |||||
Sample interval=sec/div÷200 | |||||
Vertical | Bandwidth(-3db) | DPO6084 | DPO6104 | DPO6204 | |
80MHz | 100MHz | 200MHz | |||
Vertical resolution | Analog channel 8bit | ||||
Digital channel 1bit | |||||
Vertical scale range | input BNC position is 500μV/div~10V/div | ||||
Position range | 500μV/div to 120mV/div,±1V | ||||
122mV/div to 1.2V/div,±10V | |||||
1.22V/div to 10V/div,±50V | |||||
Optional analog bandwidth limitation | Typical 20MHz | ||||
Bass response(-3db) | In BNC position is≤10Hz | ||||
Rising time in BNC position,typical | DPO6084 | DPO6104 | DPO6204 | ||
≤4.4ns | ≤3.5ns | ≤1.8ns | |||
Vertical gain accuracy | In “normal” or “average” acquisition mode,the accuracy of 10V/div to 10mV/div is ±3% | ||||
In “normal” or “average” acquisition mode,the accuracy of 5mV/div to 500uV/div is ±4%. | |||||
DC offset accuracy | ±0.1 div±2 mV±1% offset value | ||||
The isolation of channels | DC maximum bandwidth:>40 dB | ||||
Note: Bandwidth reduced to 6MHz when using a 1X probe | |||||
Trigger | Trigger level range | ±5 divisions from the center of the screen | |||
Trigger mode | auto、general、single | ||||
Level | CH1~CH4 | ±4 divisions from the center of the screen | |||
Holdoff range | 8ns~10s | ||||
Trigger level accuracy | CH1~CH4 | 0.2 div×volts/div within ±4 divisions from the center of the screen | |||
Edge trigger | Slope | Rising edge,falling edge,rising or falling edge | |||
Signal source | CH1~CH4, | ||||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Pulse width trigger | Polarity | Positive polarity,negative polarity | |||
Condition(When) | <,>, !=, = | ||||
Signal source | CH1~CH4, | ||||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Pulse width range | 8ns ~ 10s | ||||
Video trigger | Signal standard | NTSC, PAL | |||
Signal source | CH1~CH2 | ||||
Synchronization | Scanning line、line number、odd field、even field、all field | ||||
Slope trigger | Slope | rise,fal | |||
condition(When) | <,>, !=, = | ||||
Signal source | CH1 ~ CH4 | ||||
Time range | 8ns ~ 10s | ||||
Overtime trigger | Signal source | CH1~CH4, | |||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Polarity | Positive polarity,negative polarity | ||||
Time range | 8ns ~ 10s | ||||
Window trigger | Signal source | CH1~CH2~CH3~CH4~LA1~LA4 | |||
Pattern trigger | Pattern | 0:low level;1:high level;X:ignore; | |||
Level(signal source) | CH1~CH4 | ||||
Interval trigger | Slope | rise,fall | |||
condition(When) | <,>, !=, = | ||||
Signal source | CH1~CH4, | ||||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Time rangeTime range | 8ns ~ 10s | ||||
Delay trigger | Edge type | Rising edge,falling edge | |||
Signal source | CH1~CH4 | ||||
condition(When) | <,>, !=, = | ||||
Time range | 8ns ~ 10s | ||||
Set up hold trigger | Edge type | Rising edge,falling edge | |||
Signal source | CH1~CH4 | ||||
condition(When) | <,>, !=, = | ||||
Time range | 8ns ~ 10s | ||||
Runt trigger | Polarity | Positive polarity,negative polarity | |||
Condition(When) | <,>, !=, = | ||||
Signal source | CH1~CH4 | ||||
Time range | 8ns ~ 10s | ||||
UART trigger | condition(When) | start、stop、data、odd-even check、reception error | |||
Signal source(RX/TX) | CH1~CH4, | ||||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Data format | Hex(hexadecimal) | ||||
Data length | 1 byte | ||||
Data bit width | 5 bit, 6 bit, 7 bit, 8 bit | ||||
Odd-even check | none、odd、even | ||||
Free level | high、low | ||||
Baud rate (optional) |
110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/11520 0/230400/380400/460400 bit/s |
||||
Baud rate(user-defined) | 300bit/s~334000bit/s | ||||
LIN trigger | condition(When) | Interval field、synchronization field、ID field、synchronization error、identifier、IDand data | |||
Signal source | CH1~CH4, | ||||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Data format | Hex(hexadecimal) | ||||
Baud rate(optional) |
110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/11520 0/230400/380400/460400 bit/s |
||||
Baud rate(user-defined) | 300bit/s~334000bit/s | ||||
CAN trigger | condition(When) | Start bit、remote frame ID、data frame ID、frame ID、remote frame data、data frame data、wrong frame、all errors、answer error、overload frame | |||
Signal source | CH1~CH4 | ||||
Data format | Hex(hexadecimal) | ||||
Baud rate(optional) |
10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000 , 250000, 500000, 800000, 1000000 |
||||
Baud rate(user-defined) | 5kbit/s~1Mbit/s | ||||
SPI trigger | Signal source | CH1~CH4, | |||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Data format | Hex(hexadecimal) | ||||
Data bit width | 4, 8, 16, 24, 32 | ||||
IIC trigger | Signal source (SDA/SCL) | CH1~CH4, | |||
D1.0~D1.3, | |||||
D2.0~D2.3, | |||||
D3.0~D3.3, | |||||
D4.0~D4.3 | |||||
Data format | Hex(hexadecimal) | ||||
Data index | 0~7 | ||||
opportunity(condition) | Start bit、stop bit、no response、address、data、restart | ||||
Measurement | cursor | Voltage difference between cursors △V | |||
Time difference between cursors △T | |||||
Reciprocal of △T,in Hertz(1/△T) | |||||
Auto measurement | frequency、period、mean、peak-to-peak、RMS、minimum、mixmum、rising time、falling time、+ width、- width、base、top、middle、amplitude、overshoot、preshoot、rising edge phase difference、falling edge phase difference、+ duty、- duty、period mean、PRMS、FOVshoot、ROVshoot、BWIDTH、FRF、FFR、LRR、LRF、LFR、LFF | ||||
DVM | Data source | CH1,CH2 | |||
Measurement type | DC effective value | ||||
AC effective value | |||||
DC | |||||
Frequency meter | hardware 6 bits frequency meter | ||||
Arbitrary waveform generator |
|||||
Arbitrary waveform generator(for oscilloscopes with signal source channels) | Channel number | 2 channels | |||
Sample rate | 200MSa/s | ||||
Vertical resolution | 12 bits | ||||
Maximum frequency | 25 MHz | ||||
Standard waveforms | sin、square、pulse、triangular,noise、DC | ||||
Sinc、index、semi-distortion、lorentz,dual tone multiple frequency,gauss,ECG | |||||
Arbitrary waveform | Arb1,Arb2,Arb3,Arb4 | ||||
Sin | Frequency range | 0.1Hz~25MHz | |||
square/pulse | Frequency range | 0.1Hz~10MHz | |||
triangular wave | Frequency range | 0.1Hz~1MHz | |||
Sampling wave | Frequency range | 0.1Hz~1MHz | |||
Index | Frequency range | 0.1Hz~5MHz | |||
Semi-distortion | Frequency range | 0.1Hz~1MHz | |||
lorentz | Frequency range | 0.1Hz~1MHz | |||
Dual tone multiple frequency | Frequency range | 0.1Hz~1MHz | |||
Gauss | Frequency range | 0.1Hz~1MHz | |||
ECG | Frequency range | 0.1Hz~1MHz | |||
Arbitrary wave | Frequency range | 0.1 Hz to 10 MHz | |||
Waveform length | 8KSa | ||||
Frequency | accuracy | 100 ppm(<10 kHz) 50 ppm(>10 kHz) | |||
resolution | 0.1 Hz or 4 bits,take the greater one | ||||
Amplitude | Output range | 10mV~7Vp-p(high impedance) | |||
5mV~3.5Vp-p(50Ω) | |||||
DC offset | range | ±3.5 V,high impedance | |||
±1.75 V,50 Ω | |||||
resolution | 100 μV or 3 bits,take the greater one | ||||
accuracy | 2%(1 kHz) | ||||
Output impedance | 50 Ω | ||||
Logic analyzer |
|||||
Logic analyzer | Input impedance,DC coupling | Digital channel | |||
(300KΩ±2%) ,(8 pF±3 pF) | |||||
Threshold value | 4 channels in 1 group adjustable threshold value | ||||
Threshold option | TTL(1.4 V) | ||||
5.0 V CMOS(+2.5 V) | |||||
3.3 V CMOS(+1.65 V) | |||||
2.5 V CMOS(+1.25 V) | |||||
1.8 V CMOS(+0.9 V) | |||||
ECL(-1.3 V) | |||||
PECL(+3.7 V) | |||||
LVDS(+1.2 V) | |||||
0V | |||||
User-defined | |||||
Threshold range | ±7.0V,10mV step by step | ||||
Threshold accuracy | ±(100mV+3% threshold setting) | ||||
Dynamic range | ±5.0V+ threshold | ||||
Minimum voltage swing | 500 mVpp | ||||
Vertical resolution | 1 bit | ||||
General specifications |
|||||
Display | Display type | 7"TFT diagonal liquid crystal | |||
Display resolution | 800(horizontal)*480(vertical)pixels | ||||
Display colour | 16 million colours(24 bits true colour) | ||||
Persistence time | minimum、1 s、5 s、10 s、30S、infinite | ||||
Display type | dot、vector | ||||
Display mode | Color temperature,gray scale | ||||
Display brightness | adjustable | ||||
Grid type | adjustable | ||||
Grid brightness | adjustable | ||||
Interface | Standard interface | USB Host,USB Device,LAN, EDU signal WIFI | |||
Aux(trigger output/PassFail )--only EDU with this interface | |||||
Optional interface | PassFail | ||||
UART | |||||
HDMI | |||||
General specifications | Probe compensator output | ||||
Output voltage ,typical | about 2Vpp input≥1MΩ load | ||||
frequency、typical | 1kHz | ||||
Power supply | 100-120VACRMS(±10%),45Hz to 440Hz,CATⅡ | ||||
120-240VACRMS(±10%),45Hz to 66Hz,CATⅡ | |||||
Power consumption | <30W | ||||
Fuse | T,3.15A,250V,5x20mm | ||||
Operating temperature | 0~50 °C (32~122 °F) | ||||
Storage temperature | -40~+71 °C (-40~159.8 °F) | ||||
Humidity | ≤+104℉(≤+40°C): ≤90% relative humidity | ||||
106℉~122℉ (+41°C ~50°C): ≤60% relative humidity | |||||
Cooling method | convection | ||||
Altitude | Operating and nonoperating | 3,000m(10,000 feet) | |||
Mechanical shock | Random vibration | 0.31 g RMS from 50Hz to 500Hz, | |||
10 minutes on each axis | |||||
Nonoperating | 2.46g RMS from 5Hz to 500Hz, | ||||
10 minutes on each axis | |||||
Operating | 50g,11ms,half-sine wave | ||||
Mechanical | Size | 318 x 140 x 150mm(length x width x height) | |||
Weight | 2900g |
MPO6004D Series Accessories Included:
Fiche technique
- Canaux d'oscilloscope
- 4
- Bande passante de l'oscilloscope
- 100
- Serie
- MPO6004D
- Taux de capture
- 400k
- Générateur de signal / Fonctions
- Oui
- Analyseur logique
- Oui
- Décodage des protocoles série
- Oui
- Écran tactile
- Oui